DecoratingPhilly.com  

There are 2 different ways in which you are able to lay a flagstone patio. The moment you are laying the patio in the sand, it is what is known as dry construction. The moment you are laying the patio on cement or concrete, it is called as wet construction. The easiest of the two for a do it yourself person is the dry construction. With the dry construction you will be able to pass up mistakes and move subject s around as you go as opposing to having the adventure of the mortar drying on you and messing up your total project. Learning how to lay flagstone is simple.

How to lay a flagstone patio

The 1 thing you will need to do is make up your mind what the size of the patio that you would like to build. You will then need to find a level place in which to start building your patio. If you set about your project on level ground it makes the task a lot easier. Laying flagstone can be very simple if you have to correct tools. Make sure that you wear gloves as well as a back brace as things can get a little hard.

Once you have chosen the site in which you will like to build your flagstone patio you will then need to make sure that you have all of your measurements and then all of the materials that you will need. Convince yourself that you section off the number of space that you will use and you can then start laying your flagstone. Start at one end and work your way across the space. Make sure that you fix any mistakes that you may come across during the laying process. Make sure that you hit each piece down with a rubber mallet. later on all of the stones have been situated and you are happy you will then need to dump some more sand on it and copse it in between the cracks.

How to lay flagstone patio? It can be a very simple job and easy for anyone to accomplish. It will also provide beauty to your home and make a very nice sitting area and you will be able to say that you have completed it on your own.

I have a great site about flagstones: http://www.howtolay-flagstone.com

If you’ve ever used a tile breaker before, you know what I’m talking about already. If however, you haven’t, you’re now in for a little lesson on speeding up your tiling job, while getting the same professional look you want. Most of the time, you will only want to use a tile breaker when working with ceramic tile. Other tile doesn’t work very well with breakers, the reason for that, is ceramic is simply clay with a glaze coating on top. Cut through the coating, and all you have left is clay – SNAP!

Snap is what you will hear when you break through the tile with the tile breaker, some people even call them tile snappers. Some companies will call them tile cutters, they all do the same thing. So, do you spend $20 on a breaker, or $120? This depends if you’re going to be doing a lot of tiling or just 1 or two jobs. You can make a $20 breaker act like a $120 one, simply by replacing the scoring wheel with a newer, more expensive one. Spraying the gliding bars with a lubricant like WD40 allows the handle to slide back and forth a lot easier as the $120 breaker has ball bearings to help it slide easy.

Now that you have a tile breaker, and tile in hand, let’s get down to learning how to use it! First, pull the handle back so the wheel is at the front of the tile breaker, closest to you. Take a tile and place it underneath the gliding bars and push it up to the back fence on the breaker so it’s flat against it. If you already have a mark on the tile to be snapped, line the cutting wheel up to it, being careful not to touch the tile yet. Make sure you push the tile up against the back fence again if you had to move the tile.

Now bring the wheel up to the tile, while holding the handle. Once the wheel touches the tile put a small amount of pressure down with the bar, allowing the cutting wheel to rest on the tile. With the same amount of pressure, gently push the handle away from you to the top of the tile. You should be hearing a sizzling noise as the wheel cuts into the tile glaze. Finish the “scoring” all the way up and off the tile, don’t stop at the end.

So you’ve just scored the glaze on the tile, much like a glass cutter works. Now we have to break the tile. Bring the handle back about 1-2 inches until the breaker pad (the pad that’s in front of the wheel), to rest on the tile. Make sure the wheel is not touching the tile. Give the bar a quick downward shove, or if you wish, you can also put constant pressure on the bar and give it a quick downward push. This should break the tile down your line you just scored, if it doesn’t, try pushing down again. If after 3 tries, the tile still doesn’t break, take it out and start again. NEVER try to re-score the tile as this will surely damage your new wheel.

Once you get the hang of using a tile breaker, you’ll wonder how you ever did without it. Have fun and happy breaking!

Matt spent almost 3 years to perfect his book “A Unique Step-By-Step Guide: Making Floor Tiling Easier”. He wanted to make it as accessible as possible for people of all varying degrees of experience. From 1st time beginner, to the veteran that’s been tiling for years, this book covers everything necessary to learn floor tiling, with many shortcuts and pro tips that make the job faster and easier.

For an opportunity to either purchase the book, or receive a Free DVD on floor tiling, go to http://www.SeilingsFloors.com. Click on the FREE DVD, to discover the special promotion he has to offer.